Weed and Feed Math

Quote of the Day

Fabius used to say that the basest excuse for a commanding officer is 'I didn't think it would happen,' but I say it's the basest for anyone.

Seneca, from his book 'Of Anger.' My management failures were all from lack of imagination – I didn't think it would happen.


Introduction

Figure 1: Weed and Feed Fertilizer Bag I Found.

Two weeks ago, the grass around my garage looked pretty scraggly and weed-infested, so I decided it was time for fertilizer and weed-killer. I am not very knowledgeable about lawns and lawn care, so I decided to research online. This research is summarized in this post. Yes, it was time for some fertilizer and weed-killer.

Since the nearest lawn care store is 40 miles away and the COVID delta variant is active, I decided to dig around my garage for my old yard supplies and found a bag of a common weed and feed product that I had purchased years ago but never applied (Figure 1). There are pros and cons to this product, but it is here and easy to use.

This post will use US customary units because the product and my lawn are all specified in customary units. The bag is rated to cover 15,000 square feet of lawn. I have about 10,000 square feet of garage lawn, so I have enough for one application.

All my analysis was performed using the MapleFlow computer algebra system, which I am trying out for my engineering work.

Background

Reference

I decided to use the following sources for my information on fertilizers

  • North Carolina Department of Agriculture and Customer Services (link)
  • University of Georgia Extension Service (link)
  • Texas A&M Extension (link)

Their information is well-laid out and easy to use.

Definitions

NPK Numbers
Every fertilizer bag has a string of three numbers on it (e.g. "28-0-3"), which refers to the nitrogen (N)-phosphate (P)-potash (K) percentages by weight. The nitrogen is usually supplied by the chemical urea (CH4N2O). Phosphate (P2O5) and potash (K2O) supply phosphorus (chemical symbol P) and potassium (chemical symbol K), respectively.

This actually an inconsistent way to express these values because the numbers express nitrogen (elemental)-phosphate (compound)-potash (compound) percentages. This means you have a bit of stoichiometry to do if you want to determine the amount of phosphorus and potassium spread. However, folks usually worry about nitrogen, so it makes sense to express that percentage directly.

Parameters

There are three parameters that I want to compute.

Fertilizer Rate [lb/1000 sq. ft.]
The weight of fertilizer (lbs) applied per 1000 square feet of lawn.
Nitrogen Rate [lb/1000 sq. ft.]
The weight of nitrogen (lbs) applied per 1000 square feet of lawn.
Fertilizer Spreader Setting [unitless]
The setting on my fertilizer spreader corresponding to my desired fertilizer rate.

Analysis

Fertilizer Rate

The fertilizer rate can be computed as shown in Figure 2.

Figure 2: Fertilizer Rate Calculation.

Nitrogen Content

Texas A&M says that you should never apply more than 1 lb of nitrogen per 1000 square feet of lawn. Figure 3 shows my analysis of Scott's Weed and Feed to determine the amount of nitrogen that will be spread according to their instructions. My numbers show that 0.8 lbs of nitrogen will be spread per 1000 square feet of lawn, which is reasonable.

Figure 3: Nitrogen Density.

Figure 3: Nitrogen Density.

Ideally, I would have performed a nitrogen test on my lawn to determine exactly the amount of nitrogen that I need to apply to my lawn. As usual, I am in a hurry, and performing the testing probably isn't worth it on a lawn that is clearly low on nitrogen (my grass is thin, and has many yellow spots).

Dispenser Calibration

I use the fertilizer spreader shown in Figure 4 (Scotts EdgeGuard DLX broadcast spreader). The rate of fertilizer spread is controlled through a dial that is numbered from 2 to 15 around its circumference.

Figure M: My Fertilizer Spreader.

Figure 4: My Fertilizer Spreader.

I needed to calibrate the dial for my fertilizer to determine the correct setting for the fertilizer I am applying. I decide to apply fertilizer on three measured patches of lawn at three different settings to determine the rate versus dial setting. My test process is simple and for each test I:

  • Measured the patch of grass to get its area
  • Put fertilizer in the spreader and weigh the whole thing
  • Spread the fertilizer at the specified test setting over the test area
  • Weigh the spreader and fertilizer afterward to determine the amount of fertilizer spread
  • Record the weight of fertilizer spread, test area, and calculate the fertilizer rate.

My test data is shown in Figure 5. I started my testing with the setting S=6 because of an online recommendation. I found out that setting gave me too high a fertilizer rate.

Figure 5: Measured Pounds Per 1000 Square Foot.

I performed the linear regression shown in Figure 6. It looks like the relationship between the fertilizer rate R [lbs/1000 sq. ft.] and the spreader dial setting S is shown in Equation 1.

Eq. 1 \displaystyle R=0.665\cdot S

where

  • R is the rate of fertilizer spread [lbs/1000 ft2]
  • S is the spreader dial setting [unitless]
  • I am ignoring the intercept because it is small

Figure 6 shows the graph of my data.

Figure 6: Fertilizer Calibration Test Regression.

Figure 6: Fertilizer Calibration Test Regression.

Application Pattern

I spread the fertilizer two weeks ago and I can see that stripes in my lawn, which indicates inconsistent spreading. Next time, I will cut the application rate in half and spread the fertilizer in a criss-cross pattern (2 passes).

Conclusion

Based on my test results, I needed to set my spreader to S=2.858/0.665=4.3. I applied the fertilizer 2 weeks ago. My grass has really greened up and the weed situation is better, but there is still a weed problem. I will need to focus on this for a while.

PS

My wife watched a Youtube yard care channel (I don't know which one), and their calibration setting for the same spreader and fertilizer was 4.4. So I think my results are at least partially confirmed.

This entry was posted in Cabin. Bookmark the permalink.

3 Responses to Weed and Feed Math

  1. Filip De Somer says:

    Dear Mark, Good to see that you stay as busy as ever. I see you are now using Maple Flow instead of Mathcad. As Mathcad is slowly dying in favor of Prime, in which I have no interest, I also need to decide in which direction to go. So, I was wondering what your opinion is pro/con of Maple Flow versus Mathcad 15. Looking forward to your comments. Best regards, Filip

    • mathscinotes says:

      Hi Filip,

      Me staying busy is not a problem! I thought things would slow down as I neared retirement – that is not what is happening.

      Your question on Maple Flow versus Mathcad 15 provides me a good excuse to discuss the relative merits. If Mathcad 15 and Prime were more similar, I would not be looking at Maple Flow. However, I quickly found that Prime is so different from Mathcad 15 that I might as well consider other tools. I did do some work with Mathematica (I have a license and have used it on and off for decades), but it just does not suit my work style.

      Here is my take on the situation (3 weeks into using it):

      Maple Flow

      • Pros
      • It is working toward a similar front-end to Mathcad 15
      • Maple is the backend and it is quite powerful and easy to use
      • I have been able to follow some of their example worksheets and come up to speed pretty fast
      • Maple Soft is very receptive to receiving comments on how to improve the program — yes, I am in communication with them.
      • Cons
      • It is a new product and the GUI is a little unfriendly. I believe this will improve over time.
      • I love to use templates and styles. At this point, Maple Flow has a fairly primitive style infrastructure. I expect this to improve over time. I had extensive Mathcad 15 templates.
      • Mathcad had a useful, albeit strange, programming interface. I do not see a native programming interface in Maple Flow, though Maple has a very powerful programming interface and I am sure you can use that. However, I prefer to see a native interface.

      While I loved Mathcad 15, it is dead and I need to move on. I will experiment with Maple Flow and give them feedback on how to improve it over time. With computer algebra systems, you are forming a relationship.

      I hope this answer helps.

  2. Filip De Somer says:

    Dear Mark, Thank you for your review. I am more or less in the same situation as yourself. I am approaching retirement and looking for a good alternative for Mathcad 15, though I always enjoyed very much. I agree with you that Prime is no comparison. That and the fact that they only work on subscription makes it also from a financial side not the best choice for someone who will use the program only for his personal pleasure.
    Enjoy life, Filip

Comments are closed.